硕士邦德UV15TK是一个新的组件，高强度，中等粘度，紫外光固化环氧树脂基聚合物的粘接，密封系统，及涂层具有极高的性能。 这是一个100％反应，不含有任何溶剂或其他挥发性物质。 当暴露在紫外线光源，硕士邦德UV15TK生产耐用，结实，坚韧和耐化学腐蚀的涂料，债券和密封，具有优良的电气绝缘性能。 快速固化发生在250-365纳米波长的发光光源，在20-40毫瓦每平方厘米的能源和更快的固化强度高²。 后固化收缩率是2-3％，明显比，这是由传统的所谓自由紫外光固化composiitons激进展出。 UV15TK可用于在极宽的温度范围内-60 ° F至300 ° F。 UV15TK可以治愈，厚度可达0.030英寸。 标准粘度可以增加或减少对特定的应用队伍。 与其他许多市售的紫外光固化产品，硕士邦德UV15TK不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15TK优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 邮政UV15TK固化在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15TK在很短的时间段，如1分钟或更少，在与各商业紫外线灯的环境温度，是可以治愈的。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 UV15TK的承印物的种类繁多，包括塑料，玻璃和许多金属具有优异的附着力。 冲击强度高 – 加德纳影响测量超过320英寸＃。 UV15TK性质概括在表1。 硕士邦德UV15TK稳定储存6个月，在常温下未开封的容器。

Master Bond UV15TK is a new one component, high strength, medium viscosity, UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive and does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15TK produces durable, strong, tough and chemically resistant coatings, bonds and seals with excellent electrical insulation properties. Fast cures take place using light sources emitting at a wave length of 250-365 nm, at 20-40 milliwatts per cm² of energy and with higher intensities for faster cures. Shrinkage upon cure is 2-3%, significantly less than that which is exhibited by conventional so called free radical types of UV curable composiitons. UV15TK can be used over the exceptionally wide temperature range of -60°F to 300°F. UV15TK will cure in thicknesses up to .030 of an inch. The standard viscosity can be increased or decreased contingent on specific applications. Unlike many other commercially available UV curable products, Master Bond UV15TK is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15TK is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15TK at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15TK can be cured in very short time periods, e.g. 1 minute or less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. UV15TK has excellent adhesion to a wide variety of substrates including plastics, glass and many metals. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of UV15TK are summarized in table #1. Storage stability of Master Bond UV15TK is 6 months at room temperature in unopened containers.

硕士邦德UV15TK是一个新的组件，高强度，中等粘度，紫外光固化环氧树脂基聚合物的粘接，密封系统，及涂层具有极高的性能。 这是一个100％反应，不含有任何溶剂或其他挥发性物质。 当暴露在紫外线光源，硕士邦德UV15TK生产耐用，结实，坚韧和耐化学腐蚀的涂料，债券和密封，具有优良的电气绝缘性能。 快速固化发生在250-365纳米波长的发光光源，在20-40毫瓦每平方厘米的能源和更快的固化强度高²。 后固化收缩率是2-3％，明显比，这是由传统的所谓自由紫外光固化composiitons激进展出。 UV15TK可用于在极宽的温度范围内-60 ° F至300 ° F。 UV15TK可以治愈，厚度可达0.030英寸。 标准粘度可以增加或减少对特定的应用队伍。 与其他许多市售的紫外光固化产品，硕士邦德UV15TK不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15TK优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 邮政UV15TK固化在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15TK在很短的时间段，如1分钟或更少，在与各商业紫外线灯的环境温度，是可以治愈的。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 UV15TK的承印物的种类繁多，包括塑料，玻璃和许多金属具有优异的附着力。 冲击强度高 – 加德纳影响测量超过320英寸＃。 UV15TK性质概括在表1。 硕士邦德UV15TK稳定储存6个月，在常温下未开封的容器。

Master Bond UV15TK is a new one component, high strength, medium viscosity, UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive and does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15TK produces durable, strong, tough and chemically resistant coatings, bonds and seals with excellent electrical insulation properties. Fast cures take place using light sources emitting at a wave length of 250-365 nm, at 20-40 milliwatts per cm² of energy and with higher intensities for faster cures. Shrinkage upon cure is 2-3%, significantly less than that which is exhibited by conventional so called free radical types of UV curable composiitons. UV15TK can be used over the exceptionally wide temperature range of -60°F to 300°F. UV15TK will cure in thicknesses up to .030 of an inch. The standard viscosity can be increased or decreased contingent on specific applications. Unlike many other commercially available UV curable products, Master Bond UV15TK is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15TK is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15TK at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15TK can be cured in very short time periods, e.g. 1 minute or less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. UV15TK has excellent adhesion to a wide variety of substrates including plastics, glass and many metals. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of UV15TK are summarized in table #1. Storage stability of Master Bond UV15TK is 6 months at room temperature in unopened containers.

硕士邦德UV15TK是一个新的组件，高强度，中等粘度，紫外光固化环氧树脂基聚合物的粘接，密封系统，及涂层具有极高的性能。 这是一个100％反应，不含有任何溶剂或其他挥发性物质。 当暴露在紫外线光源，硕士邦德UV15TK生产耐用，结实，坚韧和耐化学腐蚀的涂料，债券和密封，具有优良的电气绝缘性能。 快速固化发生在250-365纳米波长的发光光源，在20-40毫瓦每平方厘米的能源和更快的固化强度高²。 后固化收缩率是2-3％，明显比，这是由传统的所谓自由紫外光固化composiitons激进展出。 UV15TK可用于在极宽的温度范围内-60 ° F至300 ° F。 UV15TK可以治愈，厚度可达0.030英寸。 标准粘度可以增加或减少对特定的应用队伍。 与其他许多市售的紫外光固化产品，硕士邦德UV15TK不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15TK优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 邮政UV15TK固化在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15TK在很短的时间段，如1分钟或更少，在与各商业紫外线灯的环境温度，是可以治愈的。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 UV15TK的承印物的种类繁多，包括塑料，玻璃和许多金属具有优异的附着力。 冲击强度高 – 加德纳影响测量超过320英寸＃。 UV15TK性质概括在表1。 硕士邦德UV15TK稳定储存6个月，在常温下未开封的容器。

Master Bond UV15TK is a new one component, high strength, medium viscosity, UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive and does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15TK produces durable, strong, tough and chemically resistant coatings, bonds and seals with excellent electrical insulation properties. Fast cures take place using light sources emitting at a wave length of 250-365 nm, at 20-40 milliwatts per cm² of energy and with higher intensities for faster cures. Shrinkage upon cure is 2-3%, significantly less than that which is exhibited by conventional so called free radical types of UV curable composiitons. UV15TK can be used over the exceptionally wide temperature range of -60°F to 300°F. UV15TK will cure in thicknesses up to .030 of an inch. The standard viscosity can be increased or decreased contingent on specific applications. Unlike many other commercially available UV curable products, Master Bond UV15TK is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15TK is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15TK at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15TK can be cured in very short time periods, e.g. 1 minute or less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. UV15TK has excellent adhesion to a wide variety of substrates including plastics, glass and many metals. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of UV15TK are summarized in table #1. Storage stability of Master Bond UV15TK is 6 months at room temperature in unopened containers.