硕士邦德UV15SP – 1是一个新的组件，高强度的紫外光固化环氧树脂基聚合物的粘接，密封系统与涂层具有极高的性能。 它是100％的反应，其中不含任何溶剂或其他挥发性物质在环境温度低粘度液体。 当暴露在紫外线光源，硕士邦德UV15SP – 1生产耐用，结实，坚韧和耐化学腐蚀的涂料和胶粘剂/密封剂，具有优良的电气绝缘性能。 获得最快的治疗方法是在250-320纳米波长的发光光源。 后固化收缩率小于传统的紫外线系统的三分之一。 固化涂料和胶粘剂/密封剂，可用于在极宽的温度范围为-60 ° F到超过300 ° F。 与其他许多市售的紫外光固化产品，硕士邦德UV15SP – 1不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15SP – 1优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 后固化UV15SP – 1在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15SP – 1可以在很短的时间段，如1分钟，在各种商业紫外灯环境温度，的治愈。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 固化涂料或胶粘剂/密封剂的耐用和坚韧，具备出色的金属和非金属基材的附着力，从bonderized钢铁到聚酯薄膜聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 表1总结典型UV15SP – 1涂料的性能。 硕士邦德UV15SP – 1的储存稳定性，是在未开封的容器通常贮存条件下的6个月。

Master Bond UV15SP-1 is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, low viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15SP-1 produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15SP-1 is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15SP-1 is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15SP-1 at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15SP-1 can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15SP-1 coatings are summarized in table #1. Storage stability of Master Bond UV15SP-1 is 6 months under the usual storage conditions in unopened containers.

硕士邦德UV15SP – 1是一个新的组件，高强度的紫外光固化环氧树脂基聚合物的粘接，密封系统与涂层具有极高的性能。 它是100％的反应，其中不含任何溶剂或其他挥发性物质在环境温度低粘度液体。 当暴露在紫外线光源，硕士邦德UV15SP – 1生产耐用，结实，坚韧和耐化学腐蚀的涂料和胶粘剂/密封剂，具有优良的电气绝缘性能。 获得最快的治疗方法是在250-320纳米波长的发光光源。 后固化收缩率小于传统的紫外线系统的三分之一。 固化涂料和胶粘剂/密封剂，可用于在极宽的温度范围为-60 ° F到超过300 ° F。 与其他许多市售的紫外光固化产品，硕士邦德UV15SP – 1不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15SP – 1优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 后固化UV15SP – 1在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15SP – 1可以在很短的时间段，如1分钟，在各种商业紫外灯环境温度，的治愈。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 固化涂料或胶粘剂/密封剂的耐用和坚韧，具备出色的金属和非金属基材的附着力，从bonderized钢铁到聚酯薄膜聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 表1总结典型UV15SP – 1涂料的性能。 硕士邦德UV15SP – 1的储存稳定性，是在未开封的容器通常贮存条件下的6个月。

Master Bond UV15SP-1 is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, low viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15SP-1 produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15SP-1 is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15SP-1 is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15SP-1 at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15SP-1 can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15SP-1 coatings are summarized in table #1. Storage stability of Master Bond UV15SP-1 is 6 months under the usual storage conditions in unopened containers.

硕士邦德UV15SP – 1是一个新的组件，高强度的紫外光固化环氧树脂基聚合物的粘接，密封系统与涂层具有极高的性能。 它是100％的反应，其中不含任何溶剂或其他挥发性物质在环境温度低粘度液体。 当暴露在紫外线光源，硕士邦德UV15SP – 1生产耐用，结实，坚韧和耐化学腐蚀的涂料和胶粘剂/密封剂，具有优良的电气绝缘性能。 获得最快的治疗方法是在250-320纳米波长的发光光源。 后固化收缩率小于传统的紫外线系统的三分之一。 固化涂料和胶粘剂/密封剂，可用于在极宽的温度范围为-60 ° F到超过300 ° F。 与其他许多市售的紫外光固化产品，硕士邦德UV15SP – 1不是氧气抑制和展品一个刻意快速固化速度，即使在环境温度空气的存在。 UV15SP – 1优越的性能配置，是由于其极为有效的阳离子催化剂的固化机理。 后固化UV15SP – 1在90 °至125 ° C为30分钟，给它一个玻璃化转变温度超过125 ° C，远远比传统型UV系统。 后固化，也有效地增强耐化学性，特别是溶剂。 硕士邦德UV15SP – 1可以在很短的时间段，如1分钟，在各种商业紫外灯环境温度，的治愈。 一个传统的200瓦/英寸介质压力汞灯建议。 即使低强度的紫外线源，可迅速获得治愈。 在固化过程中无溶剂或其他挥发性物质被释放。 固化涂料或胶粘剂/密封剂的耐用和坚韧，具备出色的金属和非金属基材的附着力，从bonderized钢铁到聚酯薄膜聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 表1总结典型UV15SP – 1涂料的性能。 硕士邦德UV15SP – 1的储存稳定性，是在未开封的容器通常贮存条件下的6个月。

Master Bond UV15SP-1 is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, low viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15SP-1 produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15SP-1 is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15SP-1 is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15SP-1 at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15SP-1 can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15SP-1 coatings are summarized in table #1. Storage stability of Master Bond UV15SP-1 is 6 months under the usual storage conditions in unopened containers.