硕士邦德UV15LV是一个新的组件，高强度紫外光固化环氧树脂基聚合物的粘接，密封系统，具有极高的性能和特性的涂层。 这是一个100％反应，在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德UV15LV产生具有优良的电绝缘性能耐用，结实，坚韧和耐化学腐蚀涂料和胶粘剂/密封剂。 最快得到治愈与在250-320纳米波长的发光光源。 治愈后的收缩率小于常规紫外线系统的三分之一。 固化后的涂料和胶粘剂/密封剂可用于在-60 ° F极宽的温度范围超过300 ° F。 与许多其他商用UV固化产品，硕士邦德UV15LV没有氧气抑制和展品，即使在环境温度下空气中存在刻意快速治愈率。 性能优越的UV15LV轮廓是由于其卓越成效阳离子催化剂的固化机制。 固化后在90 ° UV15LV至125 ° C的30分钟给它一个玻璃化转变温度超过125 ° C，远远高于传统型UV系统更高。 这篇文章固化，也提高耐化学性，特别是溶剂有效。 硕士邦德UV15LV可以治愈在很短的时间段，如1分钟，少在各种商业紫外线灯的环境温度。 一个传统的200瓦特/英寸的中压汞灯建议。 即使低强度紫外光源，可迅速治愈。 无溶剂或其他挥发性物质被释放在固化过程。 固化涂料或胶粘剂/密封剂和坚韧耐用，功能优异的附着力，以金属和非金属基材，从bonderized钢麦拉聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 典型UV15LV涂料性能列于表1。 储存硕士邦德UV15LV稳定为6个月未开封下的正常储存条件。

Master Bond UV15LV is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, medium viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15LV produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15LV is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15LV is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15LV at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15LV can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15LV coatings are summarized in table #1. Storage stability of Master Bond UV15LV is 6 months under the usual storage conditions in unopened containers.

硕士邦德UV15LV是一个新的组件，高强度紫外光固化环氧树脂基聚合物的粘接，密封系统，具有极高的性能和特性的涂层。 这是一个100％反应，在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德UV15LV产生具有优良的电绝缘性能耐用，结实，坚韧和耐化学腐蚀涂料和胶粘剂/密封剂。 最快得到治愈与在250-320纳米波长的发光光源。 治愈后的收缩率小于常规紫外线系统的三分之一。 固化后的涂料和胶粘剂/密封剂可用于在-60 ° F极宽的温度范围超过300 ° F。 与许多其他商用UV固化产品，硕士邦德UV15LV没有氧气抑制和展品，即使在环境温度下空气中存在刻意快速治愈率。 性能优越的UV15LV轮廓是由于其卓越成效阳离子催化剂的固化机制。 固化后在90 ° UV15LV至125 ° C的30分钟给它一个玻璃化转变温度超过125 ° C，远远高于传统型UV系统更高。 这篇文章固化，也提高耐化学性，特别是溶剂有效。 硕士邦德UV15LV可以治愈在很短的时间段，如1分钟，少在各种商业紫外线灯的环境温度。 一个传统的200瓦特/英寸的中压汞灯建议。 即使低强度紫外光源，可迅速治愈。 无溶剂或其他挥发性物质被释放在固化过程。 固化涂料或胶粘剂/密封剂和坚韧耐用，功能优异的附着力，以金属和非金属基材，从bonderized钢麦拉聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 典型UV15LV涂料性能列于表1。 储存硕士邦德UV15LV稳定为6个月未开封下的正常储存条件。

Master Bond UV15LV is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, medium viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15LV produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15LV is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15LV is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15LV at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15LV can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15LV coatings are summarized in table #1. Storage stability of Master Bond UV15LV is 6 months under the usual storage conditions in unopened containers.

硕士邦德UV15LV是一个新的组件，高强度紫外光固化环氧树脂基聚合物的粘接，密封系统，具有极高的性能和特性的涂层。 这是一个100％反应，在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德UV15LV产生具有优良的电绝缘性能耐用，结实，坚韧和耐化学腐蚀涂料和胶粘剂/密封剂。 最快得到治愈与在250-320纳米波长的发光光源。 治愈后的收缩率小于常规紫外线系统的三分之一。 固化后的涂料和胶粘剂/密封剂可用于在-60 ° F极宽的温度范围超过300 ° F。 与许多其他商用UV固化产品，硕士邦德UV15LV没有氧气抑制和展品，即使在环境温度下空气中存在刻意快速治愈率。 性能优越的UV15LV轮廓是由于其卓越成效阳离子催化剂的固化机制。 固化后在90 ° UV15LV至125 ° C的30分钟给它一个玻璃化转变温度超过125 ° C，远远高于传统型UV系统更高。 这篇文章固化，也提高耐化学性，特别是溶剂有效。 硕士邦德UV15LV可以治愈在很短的时间段，如1分钟，少在各种商业紫外线灯的环境温度。 一个传统的200瓦特/英寸的中压汞灯建议。 即使低强度紫外光源，可迅速治愈。 无溶剂或其他挥发性物质被释放在固化过程。 固化涂料或胶粘剂/密封剂和坚韧耐用，功能优异的附着力，以金属和非金属基材，从bonderized钢麦拉聚酯薄膜。 冲击强度高 – 加德纳影响测量超过320英寸＃。 典型UV15LV涂料性能列于表1。 储存硕士邦德UV15LV稳定为6个月未开封下的正常储存条件。

Master Bond UV15LV is a new one component, high strength UV curable epoxy resin based polymer system for bonding, sealing, & coating with exceptionally high performance properties. It is a 100% reactive, medium viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond UV15LV produces durable, strong, tough and chemically resistant coatings and adhesive/sealants with excellent electrical insulation properties. Fastest cures are obtained with light sources emitting at a wave length of 250-320 nm. Shrinkage upon cure is less than one-third that of conventional UV systems. The cured coatings and adhesive/sealants can be used over the exceptionally wide temperature range of -60°F to over 300°F. Unlike many other commercially available UV curable products, Master Bond UV15LV is not oxygen inhibited and exhibits a desirably fast cure rate at ambient temperatures even in the presence of air. The superior performance profile of UV15LV is due to its exceptionally effective cationic catalyst curing mechanism. Post curing the UV15LV at 90° to 125°C for 30 minutes will give it a glass transition temperature over 125°C, far higher than conventional type UV systems. This post cure is also effective in enhancing chemical resistance, particularly to solvents. Master Bond UV15LV can be cured in very short time periods, e.g. 1 minute and less, at ambient temperatures with various commercial UV lamps. A conventional 200 watt/inch medium pressure mercury lamp is recommended. Even with low intensity UV sources, cures can be obtained quickly. No solvents or other volatiles are released during the curing process. Cured coatings or adhesive/sealants are durable and tough and feature excellent adhesion to both metallic and nonmetallic substrates, from bonderized steel to Mylar polyester film. Impact strengths are high – Gardner impact measurements exceed 320 inch #. Properties of typical UV15LV coatings are summarized in table #1. Storage stability of Master Bond UV15LV is 6 months under the usual storage conditions in unopened containers.