硕士邦德UV15X – 2是一个新的组成部分，不黄变高性能涂料，粘合剂和异常反应速度快于紫外线辐射的紫外光固化聚合物密封剂系统。 它是100％反应在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德聚合物系统UV15X – 2的产生具有优良的电绝缘性能持久，坚韧，不黄变和耐化学腐蚀涂料和胶粘剂和密封剂。 吸收紫外线的能量最大发生在250-360纳米范围内进行。 该固化涂料，粘合剂和密封剂可用于在极宽的温度范围-60 ° F至+300 ° F。 与许多其他商用UV固化产品，硕士邦德聚合物系统UV15x – 2是不是氧气刻意抑制，呈现出快速，即使在环境温度下的空气存在固化速度。 主债券系统UV15X – 2是可以治愈的厚度在更大节相比，典型的商业市场上的UV固化聚合物系统现在。 因此UV15X – 2可以很容易治愈，厚度达1 / 4“多，使得各种电子和光电子灌封/封装应用的价值，此举性能特点是由于其独特有效的催化剂体系。硕士邦德聚合物系统UV15X -2可以治愈后，在很短的时间类型的紫外线灯，灯的距离从UV15X – 2面，对UV15X – 2使用等典型的固化时间范围部分，从不同时期的厚度短短的3秒钟，在环境温度2-3分钟200瓦/英寸的中压汞蒸气灯建议。高达500英尺/分钟，更固化生产线速度已取得的UV15X – 2薄膜聚合物系统。无溶剂或其他挥发性物质是在固化过程中释放。固化涂料，粘合剂和/或密封剂特性一批优秀的耐用性，韧性和抗热震性以及优异的附着力最好的组合了各种基材从bonderized钢不等和铝聚酯薄膜。抗冲击性能优越。

Master Bond UV15X-2 is a new one component, non-yellowing UV curable polymer system for high performance coatings, adhesives and sealants with exceptionally fast response to UV radiation. It is 100% reactive moderate viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond Polymer System UV15X-2 produces durable, tough, non-yellowing and chemically resistant coatings and adhesives and sealants with excellent electrical insulation properties. Maximum absorption of UV energy takes place in the 250-360 nanometer range. The cured coatings, adhesives and sealants can be used over the exceptionally wide temperature range of -60°F to +300°F. Unlike many other commercially available UV curing products, the Master Bond Polymer System UV15x-2 is not oxygen inhibited and exhibits a desirably fast curing rate of ambient temperatures even in the presence of air. The Master Bond System UV15X-2 can be cured in much greater section thicknesses compared to the typical commercial UV curing polymer systems now on the market. Thus UV15X-2 can be easily cured in thicknesses up to 1/4″ and more, making it of value for various electronic and optoelectronic potting/encapsulation applications. This performance characteristic is due to its uniquely effective catalyst system. Master Bond Polymer System UV15X-2 can be cured in very short time periods depending upon type of UV lamp, distance of the lamp from the surface of the UV15X-2, thickness of the section of the UV15X-2 to be used, etc. Typical cure times range from as little as 3 seconds to 2-3 minutes at ambient temperatures. 200 watt/inch medium pressure mercury vapor lamps are recommended. Curing line speeds as high as 500 ft./minute and more have been obtained for thin films of the UV15X-2 polymer system. no solvents or other volatiles are released during the curing process. Cured coatings, adhesives and/or sealants feature a desirable combination of outstanding durability, toughness and thermal shock resistance as well as excellent adhesion to a variety of substrates ranging from bonderized steel and aluminum to polyester films. Impact resistance is superior.

硕士邦德UV15X – 2是一个新的组成部分，不黄变高性能涂料，粘合剂和异常反应速度快于紫外线辐射的紫外光固化聚合物密封剂系统。 它是100％反应在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德聚合物系统UV15X – 2的产生具有优良的电绝缘性能持久，坚韧，不黄变和耐化学腐蚀涂料和胶粘剂和密封剂。 吸收紫外线的能量最大发生在250-360纳米范围内进行。 该固化涂料，粘合剂和密封剂可用于在极宽的温度范围-60 ° F至+300 ° F。 与许多其他商用UV固化产品，硕士邦德聚合物系统UV15x – 2是不是氧气刻意抑制，呈现出快速，即使在环境温度下的空气存在固化速度。 主债券系统UV15X – 2是可以治愈的厚度在更大节相比，典型的商业市场上的UV固化聚合物系统现在。 因此UV15X – 2可以很容易治愈，厚度达1 / 4“多，使得各种电子和光电子灌封/封装应用的价值，此举性能特点是由于其独特有效的催化剂体系。硕士邦德聚合物系统UV15X -2可以治愈后，在很短的时间类型的紫外线灯，灯的距离从UV15X – 2面，对UV15X – 2使用等典型的固化时间范围部分，从不同时期的厚度短短的3秒钟，在环境温度2-3分钟200瓦/英寸的中压汞蒸气灯建议。高达500英尺/分钟，更固化生产线速度已取得的UV15X – 2薄膜聚合物系统。无溶剂或其他挥发性物质是在固化过程中释放。固化涂料，粘合剂和/或密封剂特性一批优秀的耐用性，韧性和抗热震性以及优异的附着力最好的组合了各种基材从bonderized钢不等和铝聚酯薄膜。抗冲击性能优越。

Master Bond UV15X-2 is a new one component, non-yellowing UV curable polymer system for high performance coatings, adhesives and sealants with exceptionally fast response to UV radiation. It is 100% reactive moderate viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond Polymer System UV15X-2 produces durable, tough, non-yellowing and chemically resistant coatings and adhesives and sealants with excellent electrical insulation properties. Maximum absorption of UV energy takes place in the 250-360 nanometer range. The cured coatings, adhesives and sealants can be used over the exceptionally wide temperature range of -60°F to +300°F. Unlike many other commercially available UV curing products, the Master Bond Polymer System UV15x-2 is not oxygen inhibited and exhibits a desirably fast curing rate of ambient temperatures even in the presence of air. The Master Bond System UV15X-2 can be cured in much greater section thicknesses compared to the typical commercial UV curing polymer systems now on the market. Thus UV15X-2 can be easily cured in thicknesses up to 1/4″ and more, making it of value for various electronic and optoelectronic potting/encapsulation applications. This performance characteristic is due to its uniquely effective catalyst system. Master Bond Polymer System UV15X-2 can be cured in very short time periods depending upon type of UV lamp, distance of the lamp from the surface of the UV15X-2, thickness of the section of the UV15X-2 to be used, etc. Typical cure times range from as little as 3 seconds to 2-3 minutes at ambient temperatures. 200 watt/inch medium pressure mercury vapor lamps are recommended. Curing line speeds as high as 500 ft./minute and more have been obtained for thin films of the UV15X-2 polymer system. no solvents or other volatiles are released during the curing process. Cured coatings, adhesives and/or sealants feature a desirable combination of outstanding durability, toughness and thermal shock resistance as well as excellent adhesion to a variety of substrates ranging from bonderized steel and aluminum to polyester films. Impact resistance is superior.

硕士邦德UV15X – 2是一个新的组成部分，不黄变高性能涂料，粘合剂和异常反应速度快于紫外线辐射的紫外光固化聚合物密封剂系统。 它是100％反应在常温下不含有任何溶剂或其他挥发性物质中等粘度液体。 当暴露在紫外线光源，硕士邦德聚合物系统UV15X – 2的产生具有优良的电绝缘性能持久，坚韧，不黄变和耐化学腐蚀涂料和胶粘剂和密封剂。 吸收紫外线的能量最大发生在250-360纳米范围内进行。 该固化涂料，粘合剂和密封剂可用于在极宽的温度范围-60 ° F至+300 ° F。 与许多其他商用UV固化产品，硕士邦德聚合物系统UV15x – 2是不是氧气刻意抑制，呈现出快速，即使在环境温度下的空气存在固化速度。 主债券系统UV15X – 2是可以治愈的厚度在更大节相比，典型的商业市场上的UV固化聚合物系统现在。 因此UV15X – 2可以很容易治愈，厚度达1 / 4“多，使得各种电子和光电子灌封/封装应用的价值，此举性能特点是由于其独特有效的催化剂体系。硕士邦德聚合物系统UV15X -2可以治愈后，在很短的时间类型的紫外线灯，灯的距离从UV15X – 2面，对UV15X – 2使用等典型的固化时间范围部分，从不同时期的厚度短短的3秒钟，在环境温度2-3分钟200瓦/英寸的中压汞蒸气灯建议。高达500英尺/分钟，更固化生产线速度已取得的UV15X – 2薄膜聚合物系统。无溶剂或其他挥发性物质是在固化过程中释放。固化涂料，粘合剂和/或密封剂特性一批优秀的耐用性，韧性和抗热震性以及优异的附着力最好的组合了各种基材从bonderized钢不等和铝聚酯薄膜。抗冲击性能优越。

Master Bond UV15X-2 is a new one component, non-yellowing UV curable polymer system for high performance coatings, adhesives and sealants with exceptionally fast response to UV radiation. It is 100% reactive moderate viscosity liquid at ambient temperatures which does not contain any solvents or other volatiles. When exposed to a source of UV light, Master Bond Polymer System UV15X-2 produces durable, tough, non-yellowing and chemically resistant coatings and adhesives and sealants with excellent electrical insulation properties. Maximum absorption of UV energy takes place in the 250-360 nanometer range. The cured coatings, adhesives and sealants can be used over the exceptionally wide temperature range of -60°F to +300°F. Unlike many other commercially available UV curing products, the Master Bond Polymer System UV15x-2 is not oxygen inhibited and exhibits a desirably fast curing rate of ambient temperatures even in the presence of air. The Master Bond System UV15X-2 can be cured in much greater section thicknesses compared to the typical commercial UV curing polymer systems now on the market. Thus UV15X-2 can be easily cured in thicknesses up to 1/4″ and more, making it of value for various electronic and optoelectronic potting/encapsulation applications. This performance characteristic is due to its uniquely effective catalyst system. Master Bond Polymer System UV15X-2 can be cured in very short time periods depending upon type of UV lamp, distance of the lamp from the surface of the UV15X-2, thickness of the section of the UV15X-2 to be used, etc. Typical cure times range from as little as 3 seconds to 2-3 minutes at ambient temperatures. 200 watt/inch medium pressure mercury vapor lamps are recommended. Curing line speeds as high as 500 ft./minute and more have been obtained for thin films of the UV15X-2 polymer system. no solvents or other volatiles are released during the curing process. Cured coatings, adhesives and/or sealants feature a desirable combination of outstanding durability, toughness and thermal shock resistance as well as excellent adhesion to a variety of substrates ranging from bonderized steel and aluminum to polyester films. Impact resistance is superior.