EP36

硕士邦德聚合物体系EP36是一个独特的一个组成部分的高性能电器灌封增韧环氧树脂体系，铸造，封装，烘烤涂料和胶粘剂应用。 它具有出色的组合，包括高温稳定性高达500 ° F，出色的在极宽的温度范围为-80 ° F至500 ° F时，优良的物理强度，优良的金属和非金属基材的附着力，优良的抗热震性耐化学性，加上卓越的电气绝缘特性。 硕士邦德聚合物体系EP36提供额外的便利的一个组成部分系统具有灵活的固化时间表。 硕士邦德EP36是一种混合型的环氧树脂系统，能提供优良的韧性，同时在高温下优异的耐热性。 EP36有一个独特的化学性质，这使得该产品可以在不牺牲机械，电气，热性能的坚韧和耐热。 在100 ° C，EP36邵氏D硬度为35。 随着温度的升高，硬度降低，仍然不够强硬，让热循环和优良的耐热性。 EP36硕士邦德聚合物系统提供了坚实的，它必须在华氏180度加热成液体状态在强制空气或传统烤箱。 一旦液化，它是可以治愈的温度从250 ° F到350 ° F和更高。 凝胶时间和固化时间表取决于主要取决于温度。 一个典型的凝胶时间为30至60分钟，在300 ° F。 可以达到完全固化在较高的温度为300 ° F或较短的时间周期约3-5小时，在进一步加热。 硕士邦德聚合物体系EP36相关的物理性质，化学性质概括在表1。 硕士邦德聚合物系统EP36完全符合MIL – T – 27E H类或电气绝缘ü服务要求。 它已成功地经受住了超过1000小时的服务，在温度高达500 ° F。

Master Bond Polymer System EP36 is a unique one component high performance toughened epoxy system for electrical potting, casting, encapsulation, baked coatings and adhesive applications. It features an outstanding combination of properties including high temperature stability up to 500°F, outstanding thermal shock resistance over the exceptionally wide temperature range of -80°F to 500°F, superior physical strength, excellent adhesion to metallic and nonmetallic substrates, excellent chemical resistance plus superior electrical insulation characteristics. Master Bond Polymer System EP36 offers the additional convenience of being a one component system together with flexible cure schedules. Master Bond EP36 is a hybrid epoxy system which offers excellent toughness and at the same time has outstanding heat resistance at high temperatures. EP36 has a unique chemistry which allows the product to be both tough and heat resistant without sacrificing mechanical, electrical, or thermal properties. At 100°C, EP36 has a Shore D hardness of 35. As the temperature increases, the hardness will decrease and remain tough enough to allow for thermal cycling and excellent heat resistance. Master Bond Polymer System EP36 is supplied as a solid, it must be heated in a forced air or conventional oven at 180°F to get it into a liquid state. Once liquified, it can be cured at temperatures ranging from 250°F to 350°F and higher. Gel times and cure schedules depend primarily upon temperature. A typical gel time is 30 to 60 minutes at 300°F. Full cure can be achieved by further heating for about 3-5 hours at 300°F or shorter time periods at higher temperatures. Pertinent physical properties of the Master Bond Polymer System EP36 are summarized in Table #1. Master Bond Polymer System EP36 fully meets Mil-T-27E Class H or U service requirements for electrical insulation. It has successfully withstood more than 1000 hours of service at temperatures as high as 500°F.