硕士邦德X – 5TC是氧化铝填充，热传导弹性体为基础的，一个用于高性能的粘接和密封胶组成部分。 这导热胶债券以及在这两个剪切和剥离类似和不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德X – 5TC含有酮溶剂的蒸发与治疗所得少量（6％）。 初始设置需要尽快大部分的溶剂蒸发硕士邦德X – 5TC地方。 这一初始设置强度通常足以维持集会，并与一些粘附，将超过材料的强度。 粘结强度会随着溶剂的蒸发进展，达到最大时的溶剂全部已被删除。 硕士邦德X – 5TC胶粘剂有94％的重量固体含量。 所有表面应仔细清洗，并在申请前干燥。 他们应该为达到最佳效果的油脂，油，灰尘和其他污染物。 如溶剂清洗，蒸汽脱脂，蚀刻等传统清洗方法是适用的。 一个决定何时清理已经完成，通过简便的方法是流过一个垂直举行涂层表面水。 如果水逃跑中连续膜，清洁是令人满意的。 硕士邦德X – 5TC是一种易流动粘贴。 它可以稀释与酮溶剂降低粘度。 固化硕士邦德X – 5TC粘合剂具有很高的热导率11.2 BTU•在/平方英尺•小时•° F（0.003 ca​​l-cm/sec厘米² ° C）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德X – 5TC是氧化铝填充，热传导弹性体为基础的，一个用于高性能的粘接和密封胶组成部分。 这导热胶债券以及在这两个剪切和剥离类似和不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德X – 5TC含有酮溶剂的蒸发与治疗所得少量（6％）。 初始设置需要尽快大部分的溶剂蒸发硕士邦德X – 5TC地方。 这一初始设置强度通常足以维持集会，并与一些粘附，将超过材料的强度。 粘结强度会随着溶剂的蒸发进展，达到最大时的溶剂全部已被删除。 硕士邦德X – 5TC胶粘剂有94％的重量固体含量。 所有表面应仔细清洗，并在申请前干燥。 他们应该为达到最佳效果的油脂，油，灰尘和其他污染物。 如溶剂清洗，蒸汽脱脂，蚀刻等传统清洗方法是适用的。 一个决定何时清理已经完成，通过简便的方法是流过一个垂直举行涂层表面水。 如果水逃跑中连续膜，清洁是令人满意的。 硕士邦德X – 5TC是一种易流动粘贴。 它可以稀释与酮溶剂降低粘度。 固化硕士邦德X – 5TC粘合剂具有很高的热导率11.2 BTU•在/平方英尺•小时•° F（0.003 ca​​l-cm/sec厘米² ° C）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德X – 5TC是氧化铝填充，热传导弹性体为基础的，一个用于高性能的粘接和密封胶组成部分。 这导热胶债券以及在这两个剪切和剥离类似和不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德X – 5TC含有酮溶剂的蒸发与治疗所得少量（6％）。 初始设置需要尽快大部分的溶剂蒸发硕士邦德X – 5TC地方。 这一初始设置强度通常足以维持集会，并与一些粘附，将超过材料的强度。 粘结强度会随着溶剂的蒸发进展，达到最大时的溶剂全部已被删除。 硕士邦德X – 5TC胶粘剂有94％的重量固体含量。 所有表面应仔细清洗，并在申请前干燥。 他们应该为达到最佳效果的油脂，油，灰尘和其他污染物。 如溶剂清洗，蒸汽脱脂，蚀刻等传统清洗方法是适用的。 一个决定何时清理已经完成，通过简便的方法是流过一个垂直举行涂层表面水。 如果水逃跑中连续膜，清洁是令人满意的。 硕士邦德X – 5TC是一种易流动粘贴。 它可以稀释与酮溶剂降低粘度。 固化硕士邦德X – 5TC粘合剂具有很高的热导率11.2 BTU•在/平方英尺•小时•° F（0.003 ca​​l-cm/sec厘米² ° C）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德X – 5TC是氧化铝填充，热传导弹性体为基础的，一个用于高性能的粘接和密封胶组成部分。 这导热胶债券以及在这两个剪切和剥离类似和不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德X – 5TC含有酮溶剂的蒸发与治疗所得少量（6％）。 初始设置需要尽快大部分的溶剂蒸发硕士邦德X – 5TC地方。 这一初始设置强度通常足以维持集会，并与一些粘附，将超过材料的强度。 粘结强度会随着溶剂的蒸发进展，达到最大时的溶剂全部已被删除。 硕士邦德X – 5TC胶粘剂有94％的重量固体含量。 所有表面应仔细清洗，并在申请前干燥。 他们应该为达到最佳效果的油脂，油，灰尘和其他污染物。 如溶剂清洗，蒸汽脱脂，蚀刻等传统清洗方法是适用的。 一个决定何时清理已经完成，通过简便的方法是流过一个垂直举行涂层表面水。 如果水逃跑中连续膜，清洁是令人满意的。 硕士邦德X – 5TC是一种易流动粘贴。 它可以稀释与酮溶剂降低粘度。 固化硕士邦德X – 5TC粘合剂具有很高的热导率11.2 BTU•在/平方英尺•小时•° F（0.003 ca​​l-cm/sec厘米² ° C）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.