硕士邦德UV10医疗是一种单组分，UV固化系统，完全符合美国药典VI级规格。 这种低粘度，光学透明制度是优越的胶粘剂，密封剂和涂料，超出1 / 8“厚的浇注料，固化后的系统具有良好的耐化学性能尤其是消毒剂，它具有优良的粘接的基材种类繁多，尤其是玻璃和光清除塑料的UV10医疗电气绝缘性能均优于其他许多紫外线系统。工作温度范围是-60至250 ° F.与其他一些UV固化产品，低粘度硕士邦德UV10医疗不是抑制空气和展品甚至在部分厚度大于1 / 16的“一个理想的环境温度下固化速度快。 固化时间对紫外线灯，波长和发射的紫外线辐射，从UV10医疗，对被治愈部分厚度的距离顶面灯的数量的类型取决于等典型的固化时间范围从如在环境温度为2-3分钟5-10秒不大。 200瓦特/英寸的中压汞蒸气灯或同等紫外线光源建议。 最大紫外吸收发生在280-360纳米范围内进行。 无溶剂或其他蒸汽被释放在固化的过程，需要以最小的收缩从液态到固态的地方。 该UV10医疗系统的储存稳定性通常是3个月储存条件下，例如70 ° F，在原始的，未开封的容器。 该UV10医疗系统的性能配置使得它非常适合许多医疗器械生产应用环境的理想。

Master Bond UV10 Medical is a one component, UV curable system that fully meets USP Class VI specifications. This low viscosity, optically clear system is a superior adhesive, sealant and coating and is castable beyond 1/8″ thick. The cured system has good chemical resistant properties particularly to sterilants. It has excellent adhesion to a wide variety of substrates, particularly glass and optically clear plastics. The electrical insulation properties of UV10 Medical are superior to many other UV systems. Service temperature range is -60 to 250°F. Unlike some other UV curable products, the low viscosity Master Bond UV10 Medical is not inhibited by air and exhibits a desirable fast curing rate at ambient temperatures even at section thickness greater than 1/16″. Cure time depends on the type of UV lamp, the wave lengths and the amounts of the emitted UV radiation, distance of the lamp from the top surface of the UV10 Medical, the thickness of the section to be cured, etc. Typical cure times range from as little as 5-10 seconds to 2-3 minutes at ambient temperatures. 200 watt/inch medium pressure mercury vapor lamps or equivalent UV light sources are recommended. Maximum UV absorption takes place in the 280-360 nanometer range. No solvents or other vapors are released during the curing process which takes place with minimal shrinkage from the liquid to the solid state. The storage stability of the UV10 Medical system is 3 months under usual storage conditions e.g. 70°F, in original, unopened containers. The performance profile of the UV10 Medical system makes it highly desirable for many medical device manufacturing applications.

硕士邦德UV10医疗是一种单组分，UV固化系统，完全符合美国药典VI级规格。 这种低粘度，光学透明制度是优越的胶粘剂，密封剂和涂料，超出1 / 8“厚的浇注料，固化后的系统具有良好的耐化学性能尤其是消毒剂，它具有优良的粘接的基材种类繁多，尤其是玻璃和光清除塑料的UV10医疗电气绝缘性能均优于其他许多紫外线系统。工作温度范围是-60至250 ° F.与其他一些UV固化产品，低粘度硕士邦德UV10医疗不是抑制空气和展品甚至在部分厚度大于1 / 16的“一个理想的环境温度下固化速度快。 固化时间对紫外线灯，波长和发射的紫外线辐射，从UV10医疗，对被治愈部分厚度的距离顶面灯的数量的类型取决于等典型的固化时间范围从如在环境温度为2-3分钟5-10秒不大。 200瓦特/英寸的中压汞蒸气灯或同等紫外线光源建议。 最大紫外吸收发生在280-360纳米范围内进行。 无溶剂或其他蒸汽被释放在固化的过程，需要以最小的收缩从液态到固态的地方。 该UV10医疗系统的储存稳定性通常是3个月储存条件下，例如70 ° F，在原始的，未开封的容器。 该UV10医疗系统的性能配置使得它非常适合许多医疗器械生产应用环境的理想。

Master Bond UV10 Medical is a one component, UV curable system that fully meets USP Class VI specifications. This low viscosity, optically clear system is a superior adhesive, sealant and coating and is castable beyond 1/8″ thick. The cured system has good chemical resistant properties particularly to sterilants. It has excellent adhesion to a wide variety of substrates, particularly glass and optically clear plastics. The electrical insulation properties of UV10 Medical are superior to many other UV systems. Service temperature range is -60 to 250°F. Unlike some other UV curable products, the low viscosity Master Bond UV10 Medical is not inhibited by air and exhibits a desirable fast curing rate at ambient temperatures even at section thickness greater than 1/16″. Cure time depends on the type of UV lamp, the wave lengths and the amounts of the emitted UV radiation, distance of the lamp from the top surface of the UV10 Medical, the thickness of the section to be cured, etc. Typical cure times range from as little as 5-10 seconds to 2-3 minutes at ambient temperatures. 200 watt/inch medium pressure mercury vapor lamps or equivalent UV light sources are recommended. Maximum UV absorption takes place in the 280-360 nanometer range. No solvents or other vapors are released during the curing process which takes place with minimal shrinkage from the liquid to the solid state. The storage stability of the UV10 Medical system is 3 months under usual storage conditions e.g. 70°F, in original, unopened containers. The performance profile of the UV10 Medical system makes it highly desirable for many medical device manufacturing applications.