硕士邦德MASTERSIL 800和801的化合物准备使用的具有突出的耐热性单组分高性能粘结无腐蚀性有机硅弹性体化合物，密封，防护涂料，形成就地垫片高达300 ° C（572 ° F ）。 他们是黑色无腐蚀性化合物，在常温下固化具有优良的抗热震以及机械冲击和振动，以灵活的胶状固体容易。 MASTER SIL 800是一种自流平，自由流动，低粘度材料，使充填密封和封装应用分钟裂缝和空隙。 它变得粘在大约20分钟的免费在环境温度。 MASTER SIL 800和801 MASTER SIL采用一种新型的无腐蚀性固化系统，允许在部分应用他们的就业厚度达6mm（1 / 4英寸）。 使用厚度比这更大的，他们可能永远无法完全治愈。 硕士邦德建议两（2）有机硅应用组件使用厚度大于6mm节（1 / 4英寸）更大。 固化后的硕士邦德MASTER SIL 800和801的化合物具有优异的附着力，包括许多金属，玻璃，陶瓷，木材和最没有一个引物援助最常见的塑料基板。 为了获得最大的附着力硕士邦德建议的具体硅底漆就业。 咨询掌握有关细节问题基板债券。 所有被粘合或密封表面应彻底清洗干净，如naphta，MEK或1,1,1三氯乙烷合适的溶剂清除污垢，油或油脂。 表面应擦拭干，然后再应用硅酮胶密封剂。 所有溶剂应被视为有毒an只应在通风良好的地方起诉。 暴露于高浓度的溶剂蒸汽必须避免。 凡易燃溶剂的使用，储存，混合和使用必须在通风良好的地方，远离热源，火花，明火和其他火源。

Master Bond MASTERSIL 800 and 801 compounds are ready-to-use one component high performance non-corrosive silicone elastomer compounds for bonding, sealing, protective coatings and formed-in-place gaskets with outstanding heat resistance up to 300°C (572°F). They are black non-corrosive compounds which cure readily at ambient temperatures to flexible rubbery solids with excellent resistance to thermal shock as well as mechanical shocks and vibrations. MASTER SIL 800 and is a self leveling, free flowing, low viscosity material that allows filling minute crevices and voids in sealing and potting applications. It becomes tack free in approximately 20 minutes at ambient temperatures. MASTER SIL 800 and MASTER SIL 801 employ a novel non-corrosive cure system which permits their employment in applications in section thicknesses up to 6mm (1/4 inch). used in thicknesses greater than this they may never cure fully. Master Bond recommends the use of two (2) component silicones for applications with section thicknesses greater than 6mm (1/4 inch). The cured Master Bond MASTER SIL 800 and 801 compounds have excellent adhesion to most common substrates including many metals, glass, ceramics, most woods and plastics without the aid of a primer. For maximum adhesion Master Bond recommends the employment of specific silicone primers. Consult Master Bond for details regarding problem substrates. All surfaces to be bonded or sealed should be thoroughly cleaned with a suitable solvent such as naphta, MEK or 1,1,1 trichloroethane to remove dirt, oil or grease. The surfaces should be wiped dry before applying the silicone adhesive sealants. All solvents should be considered toxic an should only be sued in well ventilated areas. Exposure to high solvent vapor concentrations must be avoided. Where flammable solvents are used, storage, mixing and use must be in ventilated areas away from heat, sparks, open flames and other sources of ignition.

硕士邦德MASTERSIL 800和801的化合物准备使用的具有突出的耐热性单组分高性能粘结无腐蚀性有机硅弹性体化合物，密封，防护涂料，形成就地垫片高达300 ° C（572 ° F ）。 他们是黑色无腐蚀性化合物，在常温下固化具有优良的抗热震以及机械冲击和振动，以灵活的胶状固体容易。 MASTER SIL 800是一种自流平，自由流动，低粘度材料，使充填密封和封装应用分钟裂缝和空隙。 它变得粘在大约20分钟的免费在环境温度。 MASTER SIL 800和801 MASTER SIL采用一种新型的无腐蚀性固化系统，允许在部分应用他们的就业厚度达6mm（1 / 4英寸）。 使用厚度比这更大的，他们可能永远无法完全治愈。 硕士邦德建议两（2）有机硅应用组件使用厚度大于6mm节（1 / 4英寸）更大。 固化后的硕士邦德MASTER SIL 800和801的化合物具有优异的附着力，包括许多金属，玻璃，陶瓷，木材和最没有一个引物援助最常见的塑料基板。 为了获得最大的附着力硕士邦德建议的具体硅底漆就业。 咨询掌握有关细节问题基板债券。 所有被粘合或密封表面应彻底清洗干净，如naphta，MEK或1,1,1三氯乙烷合适的溶剂清除污垢，油或油脂。 表面应擦拭干，然后再应用硅酮胶密封剂。 所有溶剂应被视为有毒an只应在通风良好的地方起诉。 暴露于高浓度的溶剂蒸汽必须避免。 凡易燃溶剂的使用，储存，混合和使用必须在通风良好的地方，远离热源，火花，明火和其他火源。

Master Bond MASTERSIL 800 and 801 compounds are ready-to-use one component high performance non-corrosive silicone elastomer compounds for bonding, sealing, protective coatings and formed-in-place gaskets with outstanding heat resistance up to 300°C (572°F). They are black non-corrosive compounds which cure readily at ambient temperatures to flexible rubbery solids with excellent resistance to thermal shock as well as mechanical shocks and vibrations. MASTER SIL 800 and is a self leveling, free flowing, low viscosity material that allows filling minute crevices and voids in sealing and potting applications. It becomes tack free in approximately 20 minutes at ambient temperatures. MASTER SIL 800 and MASTER SIL 801 employ a novel non-corrosive cure system which permits their employment in applications in section thicknesses up to 6mm (1/4 inch). used in thicknesses greater than this they may never cure fully. Master Bond recommends the use of two (2) component silicones for applications with section thicknesses greater than 6mm (1/4 inch). The cured Master Bond MASTER SIL 800 and 801 compounds have excellent adhesion to most common substrates including many metals, glass, ceramics, most woods and plastics without the aid of a primer. For maximum adhesion Master Bond recommends the employment of specific silicone primers. Consult Master Bond for details regarding problem substrates. All surfaces to be bonded or sealed should be thoroughly cleaned with a suitable solvent such as naphta, MEK or 1,1,1 trichloroethane to remove dirt, oil or grease. The surfaces should be wiped dry before applying the silicone adhesive sealants. All solvents should be considered toxic an should only be sued in well ventilated areas. Exposure to high solvent vapor concentrations must be avoided. Where flammable solvents are used, storage, mixing and use must be in ventilated areas away from heat, sparks, open flames and other sources of ignition.

硕士邦德MASTERSIL 800和801的化合物准备使用的具有突出的耐热性单组分高性能粘结无腐蚀性有机硅弹性体化合物，密封，防护涂料，形成就地垫片高达300 ° C（572 ° F ）。 他们是黑色无腐蚀性化合物，在常温下固化具有优良的抗热震以及机械冲击和振动，以灵活的胶状固体容易。 MASTER SIL 800是一种自流平，自由流动，低粘度材料，使充填密封和封装应用分钟裂缝和空隙。 它变得粘在大约20分钟的免费在环境温度。 MASTER SIL 800和801 MASTER SIL采用一种新型的无腐蚀性固化系统，允许在部分应用他们的就业厚度达6mm（1 / 4英寸）。 使用厚度比这更大的，他们可能永远无法完全治愈。 硕士邦德建议两（2）有机硅应用组件使用厚度大于6mm节（1 / 4英寸）更大。 固化后的硕士邦德MASTER SIL 800和801的化合物具有优异的附着力，包括许多金属，玻璃，陶瓷，木材和最没有一个引物援助最常见的塑料基板。 为了获得最大的附着力硕士邦德建议的具体硅底漆就业。 咨询掌握有关细节问题基板债券。 所有被粘合或密封表面应彻底清洗干净，如naphta，MEK或1,1,1三氯乙烷合适的溶剂清除污垢，油或油脂。 表面应擦拭干，然后再应用硅酮胶密封剂。 所有溶剂应被视为有毒an只应在通风良好的地方起诉。 暴露于高浓度的溶剂蒸汽必须避免。 凡易燃溶剂的使用，储存，混合和使用必须在通风良好的地方，远离热源，火花，明火和其他火源。

Master Bond MASTERSIL 800 and 801 compounds are ready-to-use one component high performance non-corrosive silicone elastomer compounds for bonding, sealing, protective coatings and formed-in-place gaskets with outstanding heat resistance up to 300°C (572°F). They are black non-corrosive compounds which cure readily at ambient temperatures to flexible rubbery solids with excellent resistance to thermal shock as well as mechanical shocks and vibrations. MASTER SIL 800 and is a self leveling, free flowing, low viscosity material that allows filling minute crevices and voids in sealing and potting applications. It becomes tack free in approximately 20 minutes at ambient temperatures. MASTER SIL 800 and MASTER SIL 801 employ a novel non-corrosive cure system which permits their employment in applications in section thicknesses up to 6mm (1/4 inch). used in thicknesses greater than this they may never cure fully. Master Bond recommends the use of two (2) component silicones for applications with section thicknesses greater than 6mm (1/4 inch). The cured Master Bond MASTER SIL 800 and 801 compounds have excellent adhesion to most common substrates including many metals, glass, ceramics, most woods and plastics without the aid of a primer. For maximum adhesion Master Bond recommends the employment of specific silicone primers. Consult Master Bond for details regarding problem substrates. All surfaces to be bonded or sealed should be thoroughly cleaned with a suitable solvent such as naphta, MEK or 1,1,1 trichloroethane to remove dirt, oil or grease. The surfaces should be wiped dry before applying the silicone adhesive sealants. All solvents should be considered toxic an should only be sued in well ventilated areas. Exposure to high solvent vapor concentrations must be avoided. Where flammable solvents are used, storage, mixing and use must be in ventilated areas away from heat, sparks, open flames and other sources of ignition.