硕士邦德的X 5TC氧化铝填充，耐热导电橡胶为基础的，一个高性能的粘接和密封组件胶粘剂。 这导热粘合剂债券，以及在剪切和剥离相似，不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德的X 5TC含有少量的酮溶剂挥发作为固化所得（6％）。 初始设置需要尽快作为溶剂蒸发硕士邦德的X 5TC的地方。 这个初始设置的强度通常足以维持集会和一些粘附，将超过材料的强度。 粘结强度增加，溶剂进展蒸发，达到最大时，所有的溶剂已被删除。 硕士邦德的X 5TC胶粘剂固体含量的94％（重量）。 所有表面应仔细清洗和申请前干燥。 他们应无油脂，油污，灰尘和其他污染物以达到最佳的效果。 如常规清洗溶剂清洗，蒸汽脱脂，蚀刻等方法都是适用的。 确定清洗时通过已经完成的一个简便的方法是一个垂直举行的涂层表面流过的水。 如果水运行在一个连续的薄膜，清洁是令人满意的。 硕士邦德的X 5TC是一种易流动的粘贴。 它可以与酮类溶剂稀释，以降低粘度。 固化硕士邦德的X 5TC粘合剂具有一个非常高导热11.2 BTU•/英尺平方米•人力资源•° F（0.003 ca​​l-cm/sec平方厘米℃）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德的X 5TC氧化铝填充，耐热导电橡胶为基础的，一个高性能的粘接和密封组件胶粘剂。 这导热粘合剂债券，以及在剪切和剥离相似，不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德的X 5TC含有少量的酮溶剂挥发作为固化所得（6％）。 初始设置需要尽快作为溶剂蒸发硕士邦德的X 5TC的地方。 这个初始设置的强度通常足以维持集会和一些粘附，将超过材料的强度。 粘结强度增加，溶剂进展蒸发，达到最大时，所有的溶剂已被删除。 硕士邦德的X 5TC胶粘剂固体含量的94％（重量）。 所有表面应仔细清洗和申请前干燥。 他们应无油脂，油污，灰尘和其他污染物以达到最佳的效果。 如常规清洗溶剂清洗，蒸汽脱脂，蚀刻等方法都是适用的。 确定清洗时通过已经完成的一个简便的方法是一个垂直举行的涂层表面流过的水。 如果水运行在一个连续的薄膜，清洁是令人满意的。 硕士邦德的X 5TC是一种易流动的粘贴。 它可以与酮类溶剂稀释，以降低粘度。 固化硕士邦德的X 5TC粘合剂具有一个非常高导热11.2 BTU•/英尺平方米•人力资源•° F（0.003 ca​​l-cm/sec平方厘米℃）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德的X 5TC氧化铝填充，耐热导电橡胶为基础的，一个高性能的粘接和密封组件胶粘剂。 这导热粘合剂债券，以及在剪切和剥离相似，不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德的X 5TC含有少量的酮溶剂挥发作为固化所得（6％）。 初始设置需要尽快作为溶剂蒸发硕士邦德的X 5TC的地方。 这个初始设置的强度通常足以维持集会和一些粘附，将超过材料的强度。 粘结强度增加，溶剂进展蒸发，达到最大时，所有的溶剂已被删除。 硕士邦德的X 5TC胶粘剂固体含量的94％（重量）。 所有表面应仔细清洗和申请前干燥。 他们应无油脂，油污，灰尘和其他污染物以达到最佳的效果。 如常规清洗溶剂清洗，蒸汽脱脂，蚀刻等方法都是适用的。 确定清洗时通过已经完成的一个简便的方法是一个垂直举行的涂层表面流过的水。 如果水运行在一个连续的薄膜，清洁是令人满意的。 硕士邦德的X 5TC是一种易流动的粘贴。 它可以与酮类溶剂稀释，以降低粘度。 固化硕士邦德的X 5TC粘合剂具有一个非常高导热11.2 BTU•/英尺平方米•人力资源•° F（0.003 ca​​l-cm/sec平方厘米℃）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.

硕士邦德的X 5TC氧化铝填充，耐热导电橡胶为基础的，一个高性能的粘接和密封组件胶粘剂。 这导热粘合剂债券，以及在剪切和剥离相似，不同的表面，包括金属，木材，大多数塑料，陶瓷，玻璃，橡胶，造纸，皮革，墙板和保温，混凝土，塑料泡沫和石头。 硕士邦德的X 5TC含有少量的酮溶剂挥发作为固化所得（6％）。 初始设置需要尽快作为溶剂蒸发硕士邦德的X 5TC的地方。 这个初始设置的强度通常足以维持集会和一些粘附，将超过材料的强度。 粘结强度增加，溶剂进展蒸发，达到最大时，所有的溶剂已被删除。 硕士邦德的X 5TC胶粘剂固体含量的94％（重量）。 所有表面应仔细清洗和申请前干燥。 他们应无油脂，油污，灰尘和其他污染物以达到最佳的效果。 如常规清洗溶剂清洗，蒸汽脱脂，蚀刻等方法都是适用的。 确定清洗时通过已经完成的一个简便的方法是一个垂直举行的涂层表面流过的水。 如果水运行在一个连续的薄膜，清洁是令人满意的。 硕士邦德的X 5TC是一种易流动的粘贴。 它可以与酮类溶剂稀释，以降低粘度。 固化硕士邦德的X 5TC粘合剂具有一个非常高导热11.2 BTU•/英尺平方米•人力资源•° F（0.003 ca​​l-cm/sec平方厘米℃）1-2欧姆/平方米。

Master Bond X-5TC is an aluminum oxide filled, thermally conductive elastomer-based, one component adhesive for high performance bonding and sealing. This thermally conductive adhesive bonds well in both shear and peel to similar and dissimilar surfaces including metals, woods, most plastics, ceramics, glass, rubber, paper, leather, wallboard and insulation, concrete, plastic foams and stone. Master Bond X-5TC contains a small amount (6%) of a ketone solvent which evaporates as cure proceeds. An initial set takes place in Master Bond X-5TC as soon as most of the solvent has evaporated. The strength of this initial set usually suffices to maintain the assembly and, with some adherends, will exceed the strength of the material. Bond strength increases as evaporation of the solvent progresses, reaching a maximum when all of the solvent has been removed. Master Bond X-5TC adhesive has a solids content of 94% by weight. All surfaces should be carefully cleaned and dried before application. They should be free of grease, oil, dirt and other contaminants for optimal results. Conventional cleaning methods such as solvent washing, vapor degreasing, etching, etc. are applicable. A convenient way of determining when through cleaning has been accomplished is to flow water over a vertically held coated surface. If the water runs off in a continuous film, cleaning is satisfactory. Master Bond X-5TC is an easily flowable paste. It can be thinned with ketone solvents to reduce viscosity. Cured Master Bond X-5TC adhesive features a very high thermal conductivity of 11.2 BTU•in/ft²•hr•°F (0.003 cal-cm/sec cm² °C) of 1-2 ohms/square.